agilent 2.5 mm x 7.6 mm rectangular led lamps data sheet description the hlmp-r100, -0301, -0401, -0504 are solid state lamps encapsulated in a radial lead rectangular epoxy package. they utilize a tinted, diffused epoxy to provide high on-off contrast and a flat high intensity emitting surface. borderless package design allows creation of uninterrupted light emitting areas. the hlmp-r100 uses a double heterojunction (dh) absorbing substrate (as) aluminum gallium arsenide (algaas) red led chip in a light red epoxy package. this combination produces outstanding light output over a wide range of drive currents. the hlmp-0301 has a high efficiency red gaasp on gap led chip in a light red epoxy package. package dimensions hlmp-r100, hlmp-0301, hlmp-0401, hlmp-0504 features ? rectangular light emitting surface ? flat high sterance emitting surface ? stackable on 2.54 mm (0.100 inch) centers ? ideal as flush mounted panel indicators ? ideal for backlighting legends ? long life: solid state reliability ? choice of 4 bright colors ?dh as algaas red ?high efficiency red ?yellow ?high performance green ? ic compatible/low current requirements the hlmp-0401 provides a yellow gaasp on gap led chip in a yellow epoxy package. the hlmp-0504 provides a green gap led chip in a green epoxy package. 2.54 (0.100) 2.29 (0.090) 2.54 (0.100) 2.16 (0.085) 8.00 (0.315) 7.37 (0.290) 29.21 (1.15) min. cathode lead bottom view side view 1.27 (0.50) nominal notes: 1. all dimensions are in millimeters (inches). 2. an epoxy meniscus may extend about 1 mm (0.040") down the leads. 3. there is a mximum 1 taper from base to the top of lamp. 2.54 (0.100) nominal 0.46 (0.018) sq. nominal 7.62 (0.300) 7.11 (0.280) 7.62 (0.300) 6.99 (0.275)
2 selection guide luminous intensity iv (mcd) at 20 ma color part number min. typ. dh algaas red hlmp-r100 2.1 hlmp-r100-fg0xx 5.4 17.2 red hlmp-0301 2.1 hlmp-0301-c00xx 1.3 hlmp-0301-decxx 2.1 6.8 hlmp-0301-cd0xx 1.3 4.2 yellow hlmp-0401 3.6 hlmp-0401-b00xx 1.4 hlmp-0401-d00xx 3.6 hlmp-0401-cd0xx 2.2 7.2 hlmp-0401-debxx 3.6 11.4 green hlmp-0504 2.6 hlmp-0504-b00xx 1.6 hlmp-0504-decxx 4.2 13.4 hlmp-0504-cd0xx 2.6 8.4 hlmp-0504-c00xx 2.6 mechanical options 00: bulk 01: tape & reel, crimped leads 02: tape & reel, straight leads dd: ammo pack, straight leads color bin options 0: full color bin distribution b: color bins 2 & 3 only c: color bins 3 & 4 only maximum iv bin options 0: open (no maximum limit) others: please refer to the iv bin table minimum iv bin options please refer to the iv bin table color options 1. as algaas red 3. high efficiency red 4. yellow 5. green package options r,0: rectangular 2.5 mm x 7.6 mm part numbering system hlmp - x x xx - x x x xx
3 absolute maximum ratings at t a = 25 c parameter hlmp-r100 hlmp-0301 hlmp-0401 hlmp-0504 units peak forward current 300 90 60 90 ma average forward current [1] 20 25 20 25 ma dc current [2] 30 30 20 30 ma power dissipation 87 135 85 135 mw reverse voltage (i r = 100 a) 5555v transient forward current [3] (10 s pulse) 500 500 500 500 ma operating temperature range -20 to +100 -55 to +100 -55 to +100 -20 to +100 c storage temperature range -55 to +100 -55 to +100 wave soldering temperature (1.59 mm [0.063 in.] from body) 250 c for 3 seconds solder dipping temperature (1.59 mm [0.063 in.] from body) 260 c for 5 seconds notes: 1. see figure 5 to establish pulsed operating conditions. 2. for algaas red, red, and green series derate linearly from 50 c at 0.5 ma/ c. for yellow series derate linearly from 50 c at 0.2 ma/ c. 3. the transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the led die and wirebond. it is not recommended that the device be operated at peak current beyond the peak forward current listed in the absol ute maximum ratings.
4 figure 1. relative intensity vs. wavelength. electrical/optical characteristics at t a = 25 c hlmp-r100 hlmp-0301 hlmp-0401 hlmp-0504 test sym. description min. typ. max. min. typ. max. min. typ. max. min. typ. max. units conditions 2 q 1/2 included angle between half 100 100 100 100 deg. note 1. luminous fig. 6 intensity points l p peak 645 635 583 565 nm measure- wavelength ment at peak l d dominant 637 626 585 569 nm note 2. wavelength dl 1/2 spectral line 20 40 36 28 nm halfwidth t s speed of 30 90 90 500 ns response c capacitance 30 16 18 18 pf v f = 0; f = 1 mhz r q j-pin thermal 260 260 260 260 c/w junction to resistance cathode lead v f forward voltage 1.8 2.2 1.9 2.6 2.1 2.6 2.2 3.0 v i f = 20 ma figure 2. v r reverse 5.0 5.0 5.0 5.0 v i r = 100 a breakdown voltage h v luminous 80 145 500 595 lm/w note 3. efficacy notes: 1. q 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. the dominant wavelength, l d , is derived from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 3. radiant intensity, i e , in watts/steradian, may be found from the equation i e = i v / h v , where i v is the luminous intensity in candelas and h v is the luminous efficacy in lumens/watt. high efficiency red wavelength C nm relative intensity 1.0 0.5 0 500 550 600 650 700 750 yellow green t a = 25 c algaas red
5 figure 6. relative luminous intensity vs. angular displacement. figure 2. forward current vs. forward voltage. v f (300 ma) for algaas red = 2.6 volts typical. figure 3. relative luminous intensity vs. forward current. figure 4. relative efficiency (luminous intensity per unit current) vs. peak current. h v (300 ma) for algaas red = 0.7. figure 5. maximum tolerable peak current vs. peak duration (i peak max determined from temperature derated i dc max). i f C forward current C ma 1.0 v f C forward voltage C v 0 20 40 60 2.0 3.0 90 70 green yellow her algaas red 10 30 50 80 4.0 5.0 relative luminous intensity (normalized at 20 ma) 0 i dc C dc current per led C ma 0 30 515 2.5 2.0 algaas red 0.5 1.0 1.5 10 20 25 her, yellow, green peak C relative efficiency 0 i peak C peak current per led C ma 0.4 0.6 0.8 1.0 90 20 70 50 40 1.3 1.1 yellow green algaas red 0.5 0.7 0.9 1.2 30 60 80 10 her ratio of maximum tolerable peak current to maximum tolerable dc current 1 t p C pulse duration C s her, orange, yellow, and green 1.0 2.0 3.0 10,000 1000 4.0 1.5 100 10 i peak max. i dc max. 100 khz 30 khz 10 khz 3 khz 1 khz 300 hz 100 hz t p C pulse duration C s algaas red 3 1 10 10 10000 1000 100 1 3 khz 10 khz 1 khz 300 hz f C refresh rate C 100 hz 2 9 8 7 6 5 4 ratio of maximum peak current to temperature derated maximum dc current i peak max. i dc max. 10 100 40 70 20 60 80 30 50 90 0 10 20 30 40 50 60 70 80 90 1.0 0.6 0.8 0.2 0.4
intensity bin limits intensity range (mcd) color bin min. max. c0.52.4 d2.43.8 e3.86.1 f6.19.7 g 9.7 15.5 h 15.5 24.8 i 24.8 39.6 j 39.6 63.4 k 63.4 101.5 l 101.5 162.4 m 162.4 234.6 n 234.6 340.0 red o 340.0 540.0 p 540.0 850.0 q 850.0 1200.0 r 1200.0 1700.0 s 1700.0 2400.0 t 2400.0 3400.0 u 3400.0 4900.0 v 4900.0 7100.0 w 7100.0 10200.0 x 10200.0 14800.0 y 14800.0 21400.0 z 21400.0 30900.0 intensity bin limits, continued intensity range (mcd) color bin min. max. b1.62.5 c2.54.0 d4.06.5 e 6.5 10.3 f 10.3 16.6 g 16.6 26.5 h 26.5 42.3 i 42.3 67.7 j 67.7 108.2 k 108.2 173.2 yellow l 173.2 250.0 m 250.0 360.0 n 360.0 510.0 o 510.0 800.0 p 800.0 1250.0 q 1250.0 1800.0 r 1800.0 2900.0 s 2900.0 4700.0 t 4700.0 7200.0 u 7200.0 11700.0 v 11700.0 18000.0 w 18000.0 27000.0 b1.82.9 c2.94.7 d4.77.6 e 7.6 12.0 f 12.0 19.1 g 19.1 30.7 h 30.7 49.1 i 49.1 78.5 j 78.5 125.7 k 125.7 201.1 green l 201.1 289.0 m 289.0 417.0 n 417.0 680.0 o 680.0 1100.0 p 1100.0 1800.0 q 1800.0 2700.0 r 2700.0 4300.0 s 4300.0 6800.0 t 6800.0 10800.0 u 10800.0 16000.0 v 16000.0 25000.0 w 25000.0 40000.0 maximum tolerance for each bin limit is 18%. 6
www.agilent.com/semiconductors for product information and a complete list of distributors, please go to our web site. for technical assistance call: americas/canada: +1 (800) 235-0312 or (916) 788-6763 europe: +49 (0) 6441 92460 china: 10800 650 0017 hong kong: (+65) 6756 2394 india, australia, new zealand: (+65) 6755 1939 japan: (+81 3) 3335-8152(domestic/interna- tional), or 0120-61-1280(domestic only) korea: (+65) 6755 1989 singapore, malaysia, vietnam, thailand, philippines, indonesia: (+65) 6755 2044 taiwan: (+65) 6755 1843 data subject to change. copyright ?2001-2005 agilent technologies, inc. obsoletes 5988-2147en june 8, 2005 5989-3267en color categories lambda (nm) color category # min. max. 6 561.5 564.5 5 564.5 567.5 green 4 567.5 570.5 3 570.5 573.5 2 573.5 576.5 1 582.0 584.5 3 584.5 587.0 yellow 2 587.0 589.5 4 589.5 592.0 5 592.0 593.0 tolerance for each bin limit is 0.5 nm. mechanical option matrix mechanical option code definition 00 bulk packaging, minimum increment 500 pcs/bag 01 tape & reel, crimped leads, minimum increment 1300 pcs/bag 02 tape & reel, straight leads, minimum increment 1300 pcs/bag dd ammo pack, straight leads with minimum increment 2k/pack note: all categories are established for classification of products. products may not be available in all categories. please contact your local agilent representative for further clarification/information.
|
